Guys,
I have a bunch of products new and old that I now have back on the website. All Items can be purchased on www.ccracingengines.com or email This email address is being protected from spambots. You need JavaScript enabled to view it. .

CC Racing Radio Box Tape:
This is some really good tape and the rolls are huge and last a long time. The tape is 1" wide and 27 yards long and is the tape I personally use on all my boats.

$4 per roll or 6 for $20.




CC Racing Life Reciever Battery Packs
Life Battery for your radio box 6.6 volts 1800mAh. It is only 2" long by 1" tall and will fit nicely in most radio boxes. It is lightweight, high energy density battery with more power than NiCd and NiMH receiver batteries provide and at 6.6 volts there is no need for a voltage reducer like the lipo batteries. We have been using these in all of our boats for almost five years and we absolutely love them. Check around and I don't think you will find this strong of a battery (1800 mAh) in this size for this price anywhere.

LIFE 1800 mAh
2S 6.6 volts
20C
Standard Connector and Balance plug included

$24 each or 5 for $110





CC Racing Switch Kit
This is the nicest switch kit for RC Boats on the market. The mount is constructed from Billet Aluminum then black anodized to resist corrosion. It comes complete with switch, heavy duty 20 gauge wires with standard ends. It is Very easy to mount with one single hole and is waterproof. This switch kit solves all the problems of the similiar plastic style switch mounts on the market. It stays smooth and easy to use even after you tighten it up unlike the plastic ones. It has a very trick Machined Stainless push pull knob with stainless shaft. The Aluminum Mounting Nut that the push pull knob goes through has a o-ring in the middle of it and there is also a o-ring on the back side of the nut where it goes through your radio box making it completely waterproof.

**Switch Mount assembly is all aluminum
**Push Pull rod is Stainless Steel
**Complete assembly is anodized Black for corrosin resistence.
**Has o-ring seals in the mounting nut to help keep your radio box waterproof
**Comes complete with On & Off switch like seen in the pictures
**Switch has Heavy Duty 20 Gauge Wires
**Stays smooth and easy to use even after it is mounted

$15 each or 6 for $75





CC Racing Billet Shaft Saver
This is our CC Racing Super Billet Aluminum shaft saver. We listened to our customers and made these thinner then the industrial units on the market today. These are only .272 thick and are very lightweight. Simply place these on your flex shaft between your collet and stuffing tube then tighten your shaft like you normally do, then slide the saver close to your collet and tighten the stainless screw. When you use these you have some cheap added insurance for your flex shaft and expensive racing prop in case you hit something in the water or have a problem with your collet. This is one of those just in case items that you never need unless you don't have it. It weighs less then a quarter of a ounce (.20 ounce) or 5.7 grams and is a great safety item.

$4 each or 6 for $22





CC Racing Needle Clamp
The original CC Racing often copied but never duplicated Needle Clamps. I designed these about five years ago and every fly by night company on the market has copied them, but very rarely have any of them got such a simple design right. These clamp on the needles of wt257 or the new wt1048 carbs and stop your needles from coming out of adjustment. They come black anodized and fit very snug on the needles so that you do not have to overtighten the screws like some of the copy cat needle clamps on the market. You use the same flat head screwdriver to loosen or tighten the screws that you use to adjust your carb.

$5 each or 5 for $22





CC Racing Sealed Ceramic Bearings
We have had a lot of requests for our Ceramic Bearings with a seal so they can be used as the outer bearings in RCMK and other 4 bearing style bottom ends. Well now you guys finally have a high performance alternative to the industrial bearings these engines come with. We had a few different styles built and we tested different grade seals until we found this one that seems to be trouble free. Now you can have the added performance of a world class Ceramic bearing with a high grade seal that is built in the USA. Use a couple of these as the outer bearings and combine them with our normal ceramics as the two inside and you will have quality high performance bottom end.

Here are some of the advantages of Ceramic Bearings:

40% Less Friction vs Steel. Less Friction = Horsepower
60% Less Rotating Weight
Hand Built with Genuine Cerbec Ceramic balls in the USA
Less 3 to 5 Times Longer then Steel
Lower Vibration & Cooler Running Conditions

$26 each





CC Racing Ceramic Bearings
These are the new CC Racing ceramic bearings that we had made for Zenoah engines that have the right chamfer to fit the radius on the Zenoah cranks so that it still will have the correct endplay without binding. We have done extensive testing with these bearings and they have shown to make more power across the board while helping the engine to run cooler and turn more RPM. We have set over 30 world records with these bearings. These are not cheap china bearings these are high quality bearings. These will work on all engines that utilize a 6001 bearing (Zenoah, CY, Sikk, RCMK, Quickdraw, J&G and Trevor Simpson). These are legal in G1 and LS27 classes. You should see an improvement in engine performance with these bearings. These bearings are in a lot of engines that the top guys in the country are racing with even if they won't tell you. This is the only Ceramic Bearings that Quickdraw Marine recommends for there engines. If you are serious about your engine or your racing program then you need these bearings in your engine.


Here are some of the advantages of Ceramic Bearings:

40% Less Friction vs. Steel
Less Friction = Horsepower
Hand built in the USA
60% Less Rotating Weight
Less 3 to 5 Times Longer then Steel
Lower Vibration & Cooler Running Conditions

$24 Each




CC Racing High Speed Low Friction Bearing
These new steel bearings are designed just for our application. This is not a cheap industrial bearing.This is a great alternative for the factory bearings without the expense of the ceramic bearings. The ultimate bearing will still be our ceramic bearing, but these Steel bearings are the next best thing and much safer and more reliable then the factory units. They are a high speed, high temp, low friction with a nylon bearing cage that won't come apart like the standard industrial style bearings. They also are made with the correct special inner race chamfer that will work on Zenoah style cranks without causing endplay problems. This is a great way to upgrade your engine when doing a freshen up. It is a cheap safe way to free up some power and upgrade all at the same time.

$12 Each





CC Racing Gas Bag Mount
This is a very trick lightweight way to easily mount your fuel Bag in your boat. The nose and two feet are CNC machined from Billet aluminum and the two legs are stainless steel. It comes with billet washers and all stainless hardware. There is a nylon bolt with two nylon washers that screw into the billet nose that holds your bag in place without busting it. This makes it really easy to mount your IV bag in hard to get to places like in front of your engine in v-bottom style boats and also in the nose of some sport Hydro's or in the front of some Catamarans like the Aeromarine conquest or Stryker cat. It also makes them very easy to change when the time comes for a new fuel bag.

$20 each (Add fuel bag kit with tygon line and fittings for $10 extra 100,250,500 or 1000ml)